Penguin by the Anchor

Human rarely hunted penguins directly, but slowly starved them to death. Commercial large-scale capture of krill had made penguins to face undernourishment. Businessmen capture them for the rich krill omega-3s! Krill is the basis of the Antarctic food chain, including emperor penguins, Adelie penguins, blue whales, and various albatrosses feed on krill.
If there’s no krill at the south Pole, the natural ecosystem will be collapsed and penguins will be the biggest victim! The research team believes that industrial-scale capturing is one of the greatest threats to krill in Antarctic ocean. If commercial practices of krill are not stopped, the number of penguins in the near future may be reduced by 1/3.

In fact, we don’t need to grab the penguins’ food because omega-3 is widely found in human daily, such as fish, nuts, seaweed, etc. Do not be deceived by the commercial interests and the gimmicks! Do not buy krill products! It's not your health that you spend money on, but poor and helplessness for the lives of the penguins.

The design of this penguin has been completed for some time. When I learned about the crisis facing by the penguins, I hope people pay attention to this matter and reminded by my work! I then designed an ice floe with anchors hanging to clearly understand that the penguins have been invaded excessively by human. When you print this work and share the printed results, please remember to use your anchored ice floe to tell your friends that penguins in the Antarctic ocean are facing human damage!

Thanks SpiderMaker for sponsoring the creation of this work

https://www.3dspidermaker.com/
https://www.facebook.com/groups/3dspidermaker/

Material used: SpiderMaker PLA
Matt black, extinction white, orange, warm white, original leather

Design Software: SketchUp
PRINT UP+ & CR10

Printing Recommendation
Height: 0.2mm
Support Type: None
Not less than 0.75 and increase the resolution to 0.15mm when downsize printing

(ps. Because the accuracy on the printer is not the same. If the assembly parts are too loose or too tight, the parts may be reduced or enlarged to offset the assembly failure caused by the printer's tolerances.)

https://www.facebook.com/paperworkers
https://www.facebook.com/automata.create

【船錨邊的企鵝】

人類很少直接獵殺企鵝，但卻慢慢的將牠們餓死。商業性的大量捕撈磷蝦，讓企鵝面對食物不足的狀況。商人以磷蝦富含的omega-3為由而大量捕撈磷蝦！磷蝦是南極食物鏈的基礎，包括皇帝企鵝、阿德利企鵝、藍鯨及多種信天翁在內的生物都會以磷蝦為食。少了磷蝦的南極，自然生態體系將會崩潰，而最大的受害者就是企鵝！研究團隊認為工業規模捕撈是南極水域磷蝦的最大威脅之一，若不停止捕撈磷蝦這樣的商業行為，未來企鵝的數量可能將減少1/3。

事實上我們不需要去搶企鵝的食物，因為omega-3廣泛存在於人類日常食物中，例如：魚類、堅果、海藻……等。別讓商業利益炒作出的訊息與噱頭所欺騙！別購買磷蝦的製品！你花錢買的不是自己的健康，而是可憐無助企鵝們的生命。

這隻企鵝的設計完成已有一段時間，當我了解到企鵝所面臨的危機時，我期望用這作品來提醒人們注意這件事情！於是我又設計了掛著船錨的浮冰，用以明白的說出人類已經過度侵犯企鵝的領域了。當你在列印這個作品及分享列印成果時，請記得用這個掛著錨的浮冰來告訴你的朋友們，南極海域的企鵝正面臨人為的傷害！

感謝 SpiderMaker 織造者 贊助本作品之創作

使用材料 SpiderMaker PLA
消光黑色、消光白色、陽橙色、暖白色、原皮色

設計軟體 SketchUp
列印 UP+ & CR10

列印建議
層高0.2mm
免支撐
縮小列印時請別小於0.75並提提高解析度到0.15mm

(ps.因列印機之列印精確度不一，若有組合零件太鬆或太緊時，可將局部零件縮小或放大以抵銷因列印機公差所造成之組裝不順。)
https://www.youtube.com/watch?v=X0OFBxcySy4