Delphinus Airship SOA
Delphinus Airship SOA
Published 2017-07-20T13:45:13+00:00
My updated version of the Delphinus Air Ship from Skies of Arcadia.
I have updated it from the old version to be more print friendly as well as making the propellers able to spin and the turrets rotate.
I have also made the front nose able to be swapped from having the Moon Stone cannon open or closed.
some parts will have to be glued in place but for the most part they fit using pins.
All parts have been printed at 0.20 layer height at 100% scale.
If you are having issues printing the pins you can try this as a replacment.
https://www.amazon.com/dp/B07MH1CZ6T/ref=cm_sw_em_r_mt_dp_U_ToAaEbAXCSEDA
I will list the info by the .stl file names.
these are just the settings I used and are to be used as a guide, feel free to use whatever settings you wish.
Slicer software: Slic3r
Printer: Original Prusa i3 MK2
(just about any printer should print it)
File: anchors.stl
Material: PLA
Layer height: 0.20 mm
Supports: No
Rafts: Yes (I used 2 layers)
NOTE: small parts remove with caution.
______________________________________
File: crows_nest.stl
Material: PLA
Layer height: 0.20 mm
Supports: Yes
Rafts: YES (I used 2 layers)
______________________________________
File: front_blade_fin.stl
Material: PLA
Layer height: 0.20 mm
Supports: No
Rafts: No
NOTE: you will need to print 2 of each of the blades
______________________________________
File: main_cannon.stl
Material: PLA
Layer height: 0.20 mm
Supports: No
Rafts: Yes (I used 2 layers)
NOTE: you will need to print 4 of these,
I recommend on printing one at a time they seem to print better that way.
______________________________________
File: main_hull_L.stl
Material: PLA
Layer height: 0.20 mm
Supports: YES (its minor for the pin holes)
Rafts: No
NOTE: prints easy, has pin holes on bottom to align
with the other half.
______________________________________
File: main_hull_R.stl
Material: PLA
Layer height: 0.20 mm
Supports: YES (its minor for the pin holes)
Rafts: No
NOTE: prints easy, has pin holes on bottom to align
with the other half.
______________________________________
File: MSC_barrel.stl
Material: PLA
Layer height: 0.20 mm
Supports: No
Rafts: No
NOTE: the barrel is separate so it can be printed in different colors if wanted
simple glue it to the nose_msc.stl it has a pin and a hole on the barrel.
______________________________________
File: nose.stl
Material: PLA
Layer height: 0.20 mm
Supports: No
Rafts: No
NOTE: none
______________________________________
File: nose_MSC.stl
Material: PLA
Layer height: 0.20 mm
Supports: No
Rafts: No
NOTE: none
______________________________________
File: pins.stl
Material: PLA
Layer height: 0.20 mm
Supports: No
Rafts: Yes (I used 2 layers)
NOTE: pins for the main hull and the turrets. you can use 1/8 metal pins as well.
______________________________________
File: propeller_pins.stl
Material: PLA
Layer height: 0.20 mm
Supports: Yes
Rafts: Yes (I used 2 layers)
NOTE: pins for the propellers, the larger end attaches it the the main hull.
______________________________________
File: propellers.stl
Material: PLA
Layer height: 0.20 mm
Supports: Yes
Rafts: Yes (I used 2 layers)
NOTE: none
______________________________________
File: wings.stl
Material: PLA
Layer height: 0.20 mm
Supports: Yes
Rafts: No
NOTE: none
______________________________________
File: stand.stl
Material: PLA
Layer height: 0.20 mm
Supports: No
Rafts: No
NOTE: none
Date published | 20/07/2017 |
¿Cuándo tiempo lleva? | 780 - 900 minutos |
Tecnología | FDM |
Complejidad | Medio |
I made it with mostly silver and some blue filament. Took me a little longer than expected with getting the pins to fit, but i think it turned out great! Thanks Adam Wood!